Monday, August 26, 2013

Birdsmouth Mast - Day 2

Today I managed to clean down the scarf joints armed with my Farriers File - Thanks Andrew for the hint!  The scarf joints turned out well and the staves dead straight, thanks to the aluminium ladder which I rigged up hastily as a bench.

The duck tape worked fine to hold the scarf joint together while the epoxy set over night.  Additionally I lightly clamped all the staves together separated by polythene sheets against the side of the ladder which further ensured that everything was held straight in both vertical and horizontal planes.

Then assisted by Brian, we ran the staves through the planer to clean up the saw marks and reduce the staves to their final thickness, 13.6mm.   Once again the ladder made for a very serviceable outfeed table.

Once we had the staves dimensioned we cut the lengths to the approximate size of 23' which allowed us remove several feet from the least attractive ends of the staves and also resulted in the scarf joints being positioned more randomly along the mast.

Next came the process of cutting the birdsmouth V notches in the sides of the staves.  We set up the table saw using two featherboards which resulted in a consistent clan notch cut from the staves, except for the last few inches where the stave ran past the feather board.  This shouldn't cause any issue as we have cut the staves extra long by some 7 inches.

The featherboards kept manners on the staves as they were passed through the table saw, however on the second pass of each stave the saw produced needle shard cutoffs one of which was expelled into my finger with some force, resulting in a badly swollen finger...So my advice would be to be watchful for this and wear gloves, which I subsequently did and benefited from their protection as further needles were projected from the saw.

So next on the agenda is to cut the taper into the staves on the side opposite to the V notch.  I have not yet decided whether to make up a jig for te table saw or simply place all the staves side by side and use an electric and hand plane to cut out the tapers.









Read More..

Birdsmouth Mast

I decided to attempt making a birdsmouth mast which initially I viewed as beyond my capabilities but on researching further and reading extensively, I believed the hype that in fact it is quite easy and doable for the home amateur builder.

Using John O'Neil's excellent article in Duckworks Birdsmouth in Practice  I set up a spreadsheet calculating the tapers, widths and thicknesses of the staves. I elected to add 10% extra diameter over JB's specified plans and used a ratio of 15% of diameter for the thickness of the staves, which resulted in 35.6mm stave width and 13.7mm thick at the fattest part of the mast.

Ripping 14mm staves
So armed with two 35mm thick DF boards of 16' and 14', I ripped these into 14mm widths and scarfed these together to give me a selection of staves ready for cutting birdsmouth.  Some lengths had two scarfs due to knots which I removed, but generally the stock was of good straight grain and knot free...thank you Robbins Timber.

I made a scarfing jig for my table saw which has a sliding table.  This proved successful and stress free - no flying pieces and I was able to stand out of the line of fire with hands well away from the nasty parts.  I had read where people had suffered injuries using scarfing jigs on the table saw, but I'm glad to report this worked flawlessly.

The glue up was quite straightforward - thanks to help from my son - thanks Harry!.  We laid out the staves on a aluminium ladder which provided a straight bench and a straight side to clamp all the scarfs to, so I am very hopeful that we will have a selection of straight long staves from which to start machining the birdmouth v-notch and tapering.  I am going to cut off half the taper from the width and leave the remaining taper to be planed / sanded off the stave thickness which I hope will create a more uniform creation, rather than simply having the same thickness all the way up the mast.





Read More..

Sunday, August 25, 2013

Deck Beams & Stringers

A few months break from building came to an abrupt end when last week, I spent some quality time on fitting out the deck beams and stringers.  This was challenging for me but ultimately quite satisfying as there were three joints for each beam to align.  The centre stringer is reproduced from the full sized plan, so not much to go wrong there...it is curious to see that the stringer actually dips from the bow stem to the mast bulkhead, even though it rises higher than the sheer.

No doubt the expert builders can measure and cut each beam first time, but I found I had to nudge into each joint little by little.  I toyed with the idea of purchasing a bench combination disc / belt sander, but my wife reminded me that this was just a hobby and so I took the advice of an earlier commentator on this blog to buy a farriers file, which I put to good use along with may smaller Japanese file, shown here refining the sloped mortice for the deck beam.

Fitting the breasthook was deemed to be a simple affair as per JB's instructions, however, while I managed a reasonable first pass, I resorted to chalking the sheer clamps to guide me where to remove material.  Eventually, I succeeded in producing a passable example although, arguably no one will ever get to inspect it, as it will be covered by the decking....

The deck beams were cut out on the bandsaw following the camber template which I made - rising 2" over 6'.  This worked well for the mast bulkhead and beam.  However as I approached the bow the deck beams needed to have a higher camber to fit in with the profile of the stringer, which I copied faithfully from the FSP.  Also I fitted the breasthook proud of the sheerclamp to allow me profile it to the higher camber.  It will be interesting to see how the ply deck sits on tops of these.

Earlier during the summer, I fabricated the centreboard.  However it is still in its beta stage as I understand that attention to the profile dimensions will pay dividends in the boats pointing ability.  I'm unsure if the specified dimensions include the fibreglass sheething.   I have yet to glass the board - it's been many years since I used fiberglass cloth, so I'm not familiar with the current thinking on which material to use...any ideas?

I have yet to pour lead ballast into the board which should be fun!

Before glueing up the deck beams and stringer, I had to cut out the hole of the bulkhead hatch.  As JB points out this is better done at the bench before the bulkhead is fitted, alas, I omitted this step and so had the challenge of cutting out the hatch in situ.  Once again my Bosch multi-tool came to the rescue which allow me cut a fine line to start the jigsaw, as I wanted to retain the cutout to be re-purposed as the hatch door.  I decided not to use plastic hatches so I am optimistic that this plywood version will fit the bill.









Read More..

Monday, May 20, 2013

It's that time of year again....

In case anyone is curious why the blog seems to have come to a standstill, it's because my building has come to a standstill..!!  This is no time of year to be stuck inside a shed, when there's (allegedly) plenty of Wild Atlantic Spring Salmon and Irish Wild brown trout to be caught!  Also, doing a bit of sailing..

It's only temporary and I will be back building at the end of summer....

Update end of Summer....well the Salmon proved elusive but I did manage to catch a best ever wild brown trout of 7.5lbs (returned)  and a Tuna of about 40lbs (duly eaten by grateful crew on trip from Sicily to Greece!




Read More..

Saturday, March 30, 2013

Sole Beams & Bulkhead

Making reasonably progress on my Somes Sound - having gained some inspiration from fellow builders.

First I needed to fit the trunk sole beam which slants downhill towards the stern.  This necessitated removing some material from the underside of the aft end of the beam to ft against the trunk cleat.  Confusing isn't it?  I thought so, but now having built it, all seems crystal clear.  That's one of many enjoyment factors I derive from this project - staring into a sea of mist and navigating to the destination...so to speak..

 I fitted out the sole beams which sit on top of the floors and are attached to the trunk by a "beveled mortice" joint - not one I had heard of before but I assume that this was what the designer specified.

 The beams are made from Douglas Fir and dimensioned to the same thickness of the floors.  I enjoyed this process safe in the knowledge that any mistakes would be out of sight beneath the sole....as it transpired most of the joints were reasonably tight.

Getting the sole beams to fit to the floors was a little slower as I needed to pick up the curve and camber of the floors for each of the beams - 5 aside.  I relied upon a torpedo spirit level to gauge where the beams should be attached to the floors and then did a final test by running a straight edge across the span of the beams ensuring that they were level with each other.  So far so good.

Completed sole beams attached to trunk sole beam and floors
I decided not to screw the beams where they are morticed to the trunk sole beam relying upon a clamp to hold the bevel mortised joint secure, once I had a screw in the outer end of the beam where it meets the floor.  Having reviewed it today when the epoxy had cured, it seems like a good solution.

I debated about whether to add the V notch into the bulkhead to create a paneling effect.  So I bit the bullet and cut the notches using a V shaped cutter in a small router, which did a fine job.  I'm glad I did as I think it looks quite good.  Getting the bulkhead square and vertical to the waterline, required some more fine tuning, but I think it is a good fit now and ready for gluing to the hull.



Paneling effect looks quite authentic and adds relief to a large flat surface.  Cut with a V shaped router.  The grooves are in fact equidistant - the photo was taken from an angle which suggests otherwise.




The bulkhead itself seemed to be slightly warped so I had to clamp a straight board across the top of it to make sure everything was lined up correctly.  The bulkhead is positioned vertical to the waterline so I relied upon a long spirit level to ensure it was.

Next I have to glue and fit the cleats to the for'ard of the bulkhead and refine the shape of the camber on top of the bulkhead.  
Read More..

Monday, March 25, 2013

Floors Glue Up & shaping sheer clamp

One small sentence in the instructions couldn't take three days...could it?!!  But yep, gluing in the floors is quite time consuming so by the time I had refined their fitting and drilled for the screws, it was quite a slow procedure.
Each screw needed three separate drill bits to make the pilot holes, 12mm for the counter sunk portion, 6mm for the clearance and 4mm for the pilot in the keelson  - previous short cuts resulted in broken screws, swear word and general self flagellation.....



Here you can see the floors being epoxied to the hull.  A large screw secures it at the trunk down into the keelson, while further smaller screws are driven up from outside the hull at the plank laps
into the floors.  The "fillers" are screwed into the keelson acting as spacer between the floors.  On top of this sandwich a truck cleat is secured, which makes for a tight integrated structure allowing the lead keels weight to be distributed over the hull and tying in the centre board trunk structure.


Here you can see the fillers screwed and glued into between the floors before the trunk log cleat is assembled on top.  I made wood plug to fill the screw holes, which were chiseled flush before attaching the trunk log cleat.




The finished result cooking under the infrared panel to counter the unseasonable arctic weather we are experiencing.  



Meanwhile, I made up a camber template to shape the sheers and the top of the bulkhead.  The camber is specified as a 2" rise over 6'.  

 This defines the shape of the side decks and I assume will impact also on the angle of the coaming.  It looks like in my exuberance to plane the sheers, I may have over flattened the starboard sheer-clamp near stations 12 and 14, so I may have to glue back in some filler wood and re-plane before fitting the side deck...should matter as no one will ever know..unless they read it here!

I found it a good idea to mark the topside of the template as it is easy to have it the wrong side up....which might have been the reason for my flattened sheer-clamp!!





Read More..

Thursday, March 21, 2013

Bulkhead Dryfitted

Today I managed to get the bulkhead dry fitted and also refine the camber of the sheer clamps.  

Following my earlier post, I contacted John Brooks, Somes Sound 12.5 designer, who quickly reassured me that the bulkhead would be fine without having to make a new web frame also.  Fitting the bulkhead was quite slow, because I fitted the bulkhead in one piece rather than in two halves: the narrowing of the planks as you move forward creates a challenge since you have to insert the bulkhead aft of its final position where the jogs do not line up....


The specifications for shaping the sheer clamp camber call for a pattern to be made which has a rise of 2" over 6'.  This also defines the shape for the top of the bulk head in addition to the cambers of sheer clamps.  It does however cause the camber at the stem to look quite flat, but I am sure when the deck is fitted it will make sense visually.


Play came to a stop early today while cutting the cleats to support the bulkhead, my nice shiny Japanese pull saw ripped through my thumb...ouch!!


A salutary reminder to stay awake and keep flesh and tools apart......
Read More..